U-Boot 2012.07 [Standard IPQ806X.LN,unknown] (Oct 03 2018 - 18:59:17) smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000 4 MiB MMC: ipq_mmc: 0 In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS cdp: get part failed for rootfs Net: MAC1 addr:a:b:XX:dd:ff:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:a:b:XX:dd:ff:2 Disable WAN port eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 0a:0b:XX:dd:ff:01 Address in environment is cc:dd:XX:aa:ff:04 , eth1 ZyXEL zloader v2.07 (Oct 03 2018 - 19:00:54) MMC read: dev # 0, block # 16418, count 4 ... MMC read: dev # 0, block # 16418, count 4 ... Multiboot clinent version: 2.0 Mac1 unit failed Hit any key to stop autoboot: 3 [trimmed] NBG6817> help ATEN x[,y] set BootExtension Debug Flag (y=password) ATSE x show the seed of password generator ATSH dump manufacturer related data in ROM ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) ATGO boot up whole system ATUR x upgrade RAS image (filename) NBG6817> atgo MMC read: dev # 0, block # 18466, count 8192 ... 8192 blocks read: OK Image Name: ARM OpenWrt Linux-5.4.119 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2746210 Bytes = 2.6 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK device nand1 , # parts = 8 #: name size offset mask_flags 0: SBL 0x000c0000 0x00000000 1 1: TZ 0x00040000 0x000c0000 1 2: RPM 0x00040000 0x00100000 1 3: u-boot 0x00080000 0x00140000 1 4: env 0x00010000 0x001c0000 1 5: ART 0x00010000 0x001d0000 1 6: dualflag 0x00010000 0x001e0000 0 7: reserved 0x00210000 0x001f0000 0 active partition: nand1,0 - (SBL) 0x000c0000 @ 0x00000000 defaults: mtdids : none mtdparts: mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,${ldr_psize}(u-boot)${readonly},${env_psize}(env)${readonly},${rfdat_psize}(ART)${readonly},${dualflag_psize}(dualflag),${reserved_psize}(reserved) Setting up atags for msm partition: SBL Setting up atags for msm partition: TZ Setting up atags for msm partition: RPM Setting up atags for msm partition: u-boot Setting up atags for msm partition: env Setting up atags for msm partition: ART Setting up atags for msm partition: dualflag Setting up atags for msm partition: reserved Using machid 0x136d from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.119 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16122-c2139eef27)) #0 SMP Fri May 28 14:04:04 2021 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NBG6817 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu s30220 r8192 d23028 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800 [ 0.000000] Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5 [ 0.000000] Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.07 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 476880K/491520K available (6259K kernel code, 196K rwdata, 916K rodata, 1024K init, 240K bss, 14640K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from 0xc0b00c18 with crng_init=0 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000018] Switching to timer-based delay loop, resolution 160ns [ 0.000222] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000241] pid_max: default: 32768 minimum: 301 [ 0.000412] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000430] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001375] CPU: Testing write buffer coherency: ok [ 0.002458] Setting up static identity map for 0x42300000 - 0x42300060 [ 0.002624] rcu: Hierarchical SRCU implementation. [ 0.003081] smp: Bringing up secondary CPUs ... [ 0.004930] smp: Brought up 1 node, 2 CPUs [ 0.004944] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.004953] CPU: All CPU(s) started in SVC mode. [ 0.014195] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.014337] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.014364] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.014496] pinctrl core: initialized pinctrl subsystem [ 0.015549] NET: Registered protocol family 16 [ 0.015859] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017138] cpuidle: using governor ladder [ 0.017201] cpuidle: using governor menu [ 0.047394] usbcore: registered new interface driver usbfs [ 0.047471] usbcore: registered new interface driver hub [ 0.047534] usbcore: registered new device driver usb [ 0.047590] pps_core: LinuxPPS API ver. 1 registered [ 0.047601] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.047639] PTP clock support registered [ 0.048353] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.049423] clocksource: Switched to clocksource dg_timer [ 0.050230] thermal_sys: Registered thermal governor 'step_wise' [ 0.052672] NET: Registered protocol family 2 [ 0.052829] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.053631] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.053669] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.053718] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.053771] TCP: Hash tables configured (established 4096 bind 4096) [ 0.053866] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.053893] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.054118] NET: Registered protocol family 1 [ 0.054170] PCI: CLS 0 bytes, default 64 [ 0.055396] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.062153] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.062167] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.100378] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.102030] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator [ 0.102158] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.102257] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.102506] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: [ 0.102569] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.102606] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.325128] qcom-pcie 1b500000.pci: Link up [ 0.325278] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.325300] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.325318] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.325333] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.325389] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.325542] pci 0000:00:00.0: supports D1 [ 0.325557] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.329419] PCI: bus0: Fast back to back transfers disabled [ 0.329847] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.330200] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.331350] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.335407] PCI: bus1: Fast back to back transfers disabled [ 0.335486] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.335510] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.335635] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.335655] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.336347] pcieport 0000:00:00.0: AER: enabled with IRQ 36 [ 0.336852] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator [ 0.336967] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.337084] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.337320] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: [ 0.337380] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.337413] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.566831] qcom-pcie 1b700000.pci: Link up [ 0.566984] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.567003] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.567019] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.567072] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.567215] pci 0001:00:00.0: supports D1 [ 0.567229] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.571106] PCI: bus0: Fast back to back transfers disabled [ 0.571434] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.571810] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.573044] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.573343] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 0.577154] PCI: bus1: Fast back to back transfers disabled [ 0.577225] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.577248] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.577380] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.577400] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.578162] pcieport 0001:00:00.0: AER: enabled with IRQ 38 [ 0.580608] L2 @ QSB rate. Forcing new rate. [ 0.580820] L2 @ 384000 KHz [ 0.580999] CPU0 @ 800000 KHz [ 0.581012] CPU1 @ QSB rate. Forcing new rate. [ 0.581140] CPU1 @ 384000 KHz [ 0.584660] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.586026] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0 [ 0.587660] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.590121] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.590169] msm_serial 16340000.serial: uartclk = 7372800 [ 0.590235] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM [ 0.590269] msm_serial: console setup on port #0 [ 1.407047] printk: console [ttyMSM0] enabled [ 1.412073] msm_serial: driver initialized [ 1.421088] loop: module loaded [ 1.422125] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 1.425092] spi-nor spi0.0: mx25u3235f (4096 Kbytes) [ 1.430527] 13 qcom-smem partitions found on MTD device spi0.0 [ 1.435415] Creating 13 MTD partitions on "spi0.0": [ 1.441160] 0x000000000000-0x000000020000 : "0:SBL1" [ 1.446762] 0x000000020000-0x000000040000 : "0:MIBIB" [ 1.451998] 0x000000040000-0x000000060000 : "0:SBL2" [ 1.456893] 0x000000060000-0x0000000a0000 : "0:SBL3" [ 1.461986] 0x0000000a0000-0x0000000b0000 : "0:DDRCONFIG" [ 1.466843] 0x0000000b0000-0x0000000c0000 : "0:SSD" [ 1.472233] 0x0000000c0000-0x000000100000 : "0:TZ" [ 1.476832] 0x000000100000-0x000000140000 : "0:RPM" [ 1.481789] 0x000000140000-0x0000001c0000 : "0:APPSBL" [ 1.486467] 0x0000001c0000-0x0000001d0000 : "0:APPSBLENV" [ 1.491778] 0x0000001d0000-0x0000001e0000 : "0:ART" [ 1.497146] 0x0000001e0000-0x0000001f0000 : "0:DUAL_FLAG" [ 1.501912] 0x0000001f0000-0x000000400000 : "0:RESERVED" [ 1.508567] libphy: ipq8064_mdio_bus: probed [ 1.527198] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii [ 2.376099] ar8327: qca,phy-rgmii-en is not specified [ 2.376628] libphy: Fixed MDIO Bus: probed [ 2.380853] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found [ 2.384130] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found [ 2.391613] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock [ 2.398232] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.404355] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000 [ 2.411807] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported [ 2.417549] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported [ 2.425361] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2 [ 2.433233] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported [ 2.438989] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported [ 2.446448] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors [ 2.453226] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors [ 2.460755] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled [ 2.467719] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.473978] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 62:94:d9:b4:91:d9 [ 2.483469] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found [ 2.490374] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found [ 2.497690] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock [ 2.504195] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.510538] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000 [ 2.517893] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported [ 2.523812] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported [ 2.531514] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2 [ 2.539332] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported [ 2.545228] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported [ 2.552601] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors [ 2.559300] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors [ 2.566940] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled [ 2.573969] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.580139] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 0a:60:bc:ef:d1:48 [ 2.589653] i2c /dev entries driver [ 2.598623] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.600028] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.608075] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 34,0 (pio) [ 2.614626] mmci-pl18x 12400000.sdcc: DMA channels RX dma0chan1, TX dma0chan2 [ 2.648970] sdhci: Secure Digital Host Controller Interface driver [ 2.648997] sdhci: Copyright(c) Pierre Ossman [ 2.654139] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.661038] NET: Registered protocol family 10 [ 2.665519] Segment Routing with IPv6 [ 2.668611] NET: Registered protocol family 17 [ 2.672351] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.676750] 8021q: 802.1Q VLAN Support v1.8 [ 2.689805] Registering SWP/SWPB emulation handler [ 2.717389] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364 [ 2.731015] s1a: Bringing 0uV into 1050000-1050000uV [ 2.731285] s1a: supplied by regulator-dummy [ 2.735234] s1b: Bringing 0uV into 1050000-1050000uV [ 2.739514] s1b: supplied by regulator-dummy [ 2.744450] s2a: Bringing 0uV into 775000-775000uV [ 2.748708] s2a: supplied by regulator-dummy [ 2.753324] s2b: Bringing 0uV into 775000-775000uV [ 2.757743] s2b: supplied by regulator-dummy [ à[ 2.771952] Waiting for root device /dev/mmcblk0p5... [ 2.805073] mmc0: new high speed MMC card at address 0001 [ 2.805800] mmcblk0: mmc0:0001 M62704 3.53 GiB [ 2.809694] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB [ 2.814028] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB [ 2.819857] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB, chardev (247:0) [ 2.827465] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 [ 2.864383] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 2.866539] Freeing unused kernel memory: 1024K [ 2.910191] Run /sbin/init as init process [ 3.154101] random: fast init done [ 3.303626] init: Console is alive [ 3.303740] init: - watchdog - [ 3.663486] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.705200] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.707569] SCSI subsystem initialized [ 3.716923] ehci-fsl: Freescale EHCI Host controller driver [ 3.717300] ehci-platform: EHCI generic platform driver [ 3.724645] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.726799] ohci-platform: OHCI generic platform driver [ 3.734779] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found [ 3.737871] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found [ 3.743846] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found [ 3.749928] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found [ 3.757482] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found [ 3.761556] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found [ 3.767212] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found [ 3.773375] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found [ 3.789095] dwc3 11000000.dwc3: Failed to get clk 'ref': -2 [ 3.850367] dwc3 10000000.dwc3: Failed to get clk 'ref': -2 [ 3.917264] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.917323] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.921963] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 3.929359] xhci-hcd xhci-hcd.0.auto: irq 44, io mem 0x11000000 [ 3.939501] hub 1-0:1.0: USB hub found [ 3.944556] hub 1-0:1.0: 1 port detected [ 3.948479] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.952435] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.957669] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.966000] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.972199] hub 2-0:1.0: USB hub found [ 3.980129] hub 2-0:1.0: 1 port detected [ 3.983877] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.987706] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 3.993200] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 4.000661] xhci-hcd xhci-hcd.1.auto: irq 45, io mem 0x10000000 [ 4.011440] hub 3-0:1.0: USB hub found [ 4.015842] hub 3-0:1.0: 1 port detected [ 4.019882] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.023726] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 4.029023] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 4.036692] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.043528] hub 4-0:1.0: USB hub found [ 4.051547] hub 4-0:1.0: 1 port detected [ 4.056127] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.064826] init: - preinit - [ 4.381434] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 4.384493] random: jshn: uninitialized urandom read (4 bytes read) [ 4.411624] random: procd: uninitialized urandom read (4 bytes read) [ 4.425024] random: jshn: uninitialized urandom read (4 bytes read) [ 4.449800] usb 3-1: new high-speed USB device number 2 using xhci-hcd Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.849406] EXT4-fs (loop0): recovery complete [ 7.850064] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 7.854921] mount_root: loading kmods from internal overlay [ 7.924885] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 7.931332] usb-storage 3-1:1.0: USB Mass Storage device detected [ 7.932662] scsi host0: usb-storage 3-1:1.0 [ 7.938583] usbcore: registered new interface driver usb-storage [ 7.946470] scsi host1: uas [ 7.948774] usbcore: registered new interface driver uas [ 7.951427] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 7.956830] scsi 1:0:0:0: Direct-Access Seagate Expansion 060E PQ: 0 ANSI: 6 [ 7.966782] sd 1:0:0:0: [sda] Spinning up disk... [ 8.186646] random: crng init done [ 8.186666] random: 3 urandom warning(s) missed due to ratelimiting [ 8.972129] scsi 0:0:0:0: Direct-Access Sony Storage Media 0100 PQ: 0 ANSI: 0 CCS [ 8.975802] sd 0:0:0:0: [sdb] 1966080 512-byte logical blocks: (1.01 GB/960 MiB) [ 8.981720] sd 0:0:0:0: [sdb] Write Protect is off [ 8.987644] sd 0:0:0:0: [sdb] No Caching mode page found [ 8.992090] sd 0:0:0:0: [sdb] Assuming drive cache: write through [ 9.009187] sdb: sdb1 sdb2 [ 9.014391] sd 0:0:0:0: [sdb] Attached SCSI removable disk [ 9.050208] .ready [ 9.051103] sd 1:0:0:0: [sda] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB) [ 9.225319] sd 1:0:0:0: [sda] Write Protect is off [ 9.225956] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.230169] sd 1:0:0:0: [sda] Optimal transfer size 33553920 bytes [ 9.247172] sda: sda1 [ 9.249619] sd 1:0:0:0: [sda] Attached SCSI disk [ 9.855096] block: attempting to load /etc/config/fstab [ 9.855277] block: unable to load configuration (fstab: Entry not found) [ 9.859174] block: no usable configuration [ 9.866987] mount_root: switching to ext4 overlay [ 9.876093] urandom-seed: Seeding with /etc/urandom.seed [ 9.975467] procd: - early - [ 9.975572] procd: - watchdog - [ 10.534294] procd: - watchdog - [ 10.538851] procd: - ubus - [ 10.600702] procd: - init - Please press Enter to activate this console. [ 10.932473] urngd: v1.0.2 started. [ 10.990954] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.992696] tun: Universal TUN/TAP device driver, 1.6 [ 11.033345] Mirror/redirect action on [ 11.036570] u32 classifier [ 11.036583] input device check on [ 11.038577] Actions configured [ 11.047076] Loading modules backported from Linux version v5.10.34-0-g0aa66717f684 [ 11.047098] Backport generated by backports.git v5.10.34-1-0-g7b5533e1 [ 11.065564] xt_time: kernel timezone is -0000 [ 11.141217] PPP generic driver version 2.4.2 [ 11.141665] NET: Registered protocol family 24 [ 11.159333] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 11.159949] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 11.166708] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 17.730358] EXT4-fs (sdb1): mounting ext2 file system using the ext4 subsystem [ 17.741966] EXT4-fs (sdb1): warning: mounting unchecked fs, running e2fsck is recommended [ 17.743923] EXT4-fs (sdb1): mounted filesystem without journal. Opts: [ 18.392593] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: [ 20.768614] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 20.768643] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 20.778976] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 [ 23.101583] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734 [ 26.617662] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 26.617687] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 26.698155] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 26.698986] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 26.983184] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 27.088232] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 27.090264] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 27.095950] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 27.575555] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 27.575590] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 27.587068] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 [ 29.907813] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734 [ 33.440622] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 33.440651] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 33.523083] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 33.523932] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 33.837769] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 33.943842] kmodloader: done loading kernel modules from /etc/modules.d/* [ 37.088597] dwmac1000: Master AXI performs any burst length [ 37.088630] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found [ 37.093053] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 37.101105] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 37.110064] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode [ 37.118148] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 37.130032] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 37.136585] br-VLAN3_guest: port 1(eth1.3) entered blocking state [ 37.140431] br-VLAN3_guest: port 1(eth1.3) entered disabled state [ 37.146762] device eth1.3 entered promiscuous mode [ 37.152765] device eth1 entered promiscuous mode [ 37.160608] br-VLAN3_guest: port 1(eth1.3) entered blocking state [ 37.162162] br-VLAN3_guest: port 1(eth1.3) entered forwarding state [ 37.206960] br-VLAN4_anon: port 1(eth1.4) entered blocking state [ 37.206984] br-VLAN4_anon: port 1(eth1.4) entered disabled state [ 37.212233] device eth1.4 entered promiscuous mode [ 37.222064] br-VLAN4_anon: port 1(eth1.4) entered blocking state [ 37.222621] br-VLAN4_anon: port 1(eth1.4) entered forwarding state [ 37.245787] br-lan: port 1(eth1.1) entered blocking state [ 37.245811] br-lan: port 1(eth1.1) entered disabled state [ 37.253821] device eth1.1 entered promiscuous mode [ 37.259023] br-lan: port 1(eth1.1) entered blocking state [ 37.260296] br-lan: port 1(eth1.1) entered forwarding state [ 37.277499] dwmac1000: Master AXI performs any burst length [ 37.277527] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found [ 37.281975] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 37.290045] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 37.298893] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode [ 37.306305] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 37.316881] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 38.179854] IPv6: ADDRCONF(NETDEV_CHANGE): br-VLAN3_guest: link becomes ready [ 44.454728] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 44.454754] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 44.537226] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 44.538081] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 44.964658] ath10k_pci 0001:01:00.0: rts threshold -1 [ 44.964972] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 44.976451] br-lan: port 2(wlan1) entered blocking state [ 44.979641] br-lan: port 2(wlan1) entered disabled state [ 44.985454] device wlan1 entered promiscuous mode [ 44.990579] br-lan: port 2(wlan1) entered blocking state [ 44.994990] br-lan: port 2(wlan1) entered forwarding state [ 45.022348] br-lan: port 2(wlan1) entered disabled state [ 45.081070] ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 45.359216] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 45.359374] br-lan: port 2(wlan1) entered blocking state [ 45.364703] br-lan: port 2(wlan1) entered forwarding state [ 51.269704] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 51.269824] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 51.350207] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 51.351010] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 51.727599] ath10k_pci 0000:01:00.0: rts threshold -1 [ 51.728461] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 51.738998] br-lan: port 3(wlan0) entered blocking state [ 51.742714] br-lan: port 3(wlan0) entered disabled state [ 51.748407] device wlan0 entered promiscuous mode [ 51.753624] br-lan: port 3(wlan0) entered blocking state [ 51.757986] br-lan: port 3(wlan0) entered forwarding state [ 51.763988] br-lan: port 3(wlan0) entered disabled state [ 51.775206] br-VLAN3_guest: port 2(wlan1-1) entered blocking state [ 51.775231] br-VLAN3_guest: port 2(wlan1-1) entered disabled state [ 51.780534] device wlan1-1 entered promiscuous mode [ 51.788274] ath10k_pci 0001:01:00.0: rts threshold -1 [ 51.793032] br-VLAN3_guest: port 2(wlan1-1) entered blocking state [ 51.796432] br-VLAN3_guest: port 2(wlan1-1) entered forwarding state [ 51.845828] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready [ 51.848377] br-VLAN4_anon: port 2(wlan1-2) entered blocking state [ 51.851348] br-VLAN4_anon: port 2(wlan1-2) entered disabled state [ 51.857582] device wlan1-2 entered promiscuous mode [ 51.865991] ath10k_pci 0001:01:00.0: rts threshold -1 [ 51.869802] br-VLAN4_anon: port 2(wlan1-2) entered blocking state [ 51.873387] br-VLAN4_anon: port 2(wlan1-2) entered forwarding state [ 51.887325] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-2: link becomes ready [ 52.393563] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 52.393740] br-lan: port 3(wlan0) entered blocking state [ 52.398986] br-lan: port 3(wlan0) entered forwarding state [ 52.410724] br-VLAN3_guest: port 3(wlan0-1) entered blocking state [ 52.410749] br-VLAN3_guest: port 3(wlan0-1) entered disabled state [ 52.415958] device wlan0-1 entered promiscuous mode [ 52.436366] ath10k_pci 0000:01:00.0: rts threshold -1 [ 52.443658] br-VLAN3_guest: port 3(wlan0-1) entered blocking state [ 52.443683] br-VLAN3_guest: port 3(wlan0-1) entered forwarding state [ 52.533300] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready [ 52.537396] br-VLAN4_anon: port 3(wlan0-2) entered blocking state [ 52.538818] br-VLAN4_anon: port 3(wlan0-2) entered disabled state [ 52.545325] device wlan0-2 entered promiscuous mode [ 52.564979] ath10k_pci 0000:01:00.0: rts threshold -1 [ 52.571953] br-VLAN4_anon: port 3(wlan0-2) entered blocking state [ 52.571977] br-VLAN4_anon: port 3(wlan0-2) entered forwarding state [ 52.600409] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-2: link becomes ready [ 78.987777] ath10k_pci 0000:01:00.0: Invalid peer id 1 or peer stats buffer, peer: 59706e87 sta: 00000000 [ 695.897924] ath10k_pci 0000:01:00.0: Invalid VHT mcs 15 peer stats [12843.323860] ath10k_pci 0000:01:00.0: htt tx: fixing invalid VHT TX rate code 0xff [21214.875398] br-VLAN3_guest: port 3(wlan0-1) entered disabled state [21214.875473] br-VLAN3_guest: port 2(wlan1-1) entered disabled state [21214.880505] br-VLAN3_guest: port 1(eth1.3) entered disabled state [21214.895441] device eth1.3 left promiscuous mode [21214.895561] br-VLAN3_guest: port 1(eth1.3) entered disabled state [21214.955223] device wlan0-1 left promiscuous mode [21214.955336] br-VLAN3_guest: port 3(wlan0-1) entered disabled state [21214.985438] device wlan1-1 left promiscuous mode [21214.985512] br-VLAN3_guest: port 2(wlan1-1) entered disabled state [21215.131395] br-VLAN4_anon: port 3(wlan0-2) entered disabled state [21215.131499] br-VLAN4_anon: port 2(wlan1-2) entered disabled state [21215.136639] br-VLAN4_anon: port 1(eth1.4) entered disabled state [21215.153851] device eth1.4 left promiscuous mode [21215.153951] br-VLAN4_anon: port 1(eth1.4) entered disabled state [21215.215185] device wlan0-2 left promiscuous mode [21215.215290] br-VLAN4_anon: port 3(wlan0-2) entered disabled state [21215.275710] device wlan1-2 left promiscuous mode [21215.275795] br-VLAN4_anon: port 2(wlan1-2) entered disabled state [21215.451595] br-VLAN3_guest: port 1(eth1.3) entered blocking state [21215.451621] br-VLAN3_guest: port 1(eth1.3) entered disabled state [21215.456926] device eth1.3 entered promiscuous mode [21215.471296] br-VLAN3_guest: port 2(wlan0-1) entered blocking state [21215.471325] br-VLAN3_guest: port 2(wlan0-1) entered disabled state [21215.476659] device wlan0-1 entered promiscuous mode [21215.509556] br-VLAN3_guest: port 3(wlan1-1) entered blocking state [21215.509581] br-VLAN3_guest: port 3(wlan1-1) entered disabled state [21215.527061] device wlan1-1 entered promiscuous mode [21215.532348] br-VLAN3_guest: port 3(wlan1-1) entered blocking state [21215.532375] br-VLAN3_guest: port 3(wlan1-1) entered forwarding state [21215.537561] br-VLAN3_guest: port 2(wlan0-1) entered blocking state [21215.543948] br-VLAN3_guest: port 2(wlan0-1) entered forwarding state [21215.550094] br-VLAN3_guest: port 1(eth1.3) entered blocking state [21215.556523] br-VLAN3_guest: port 1(eth1.3) entered forwarding state [21215.588650] br-VLAN4_anon: port 1(eth1.4) entered blocking state [21215.588676] br-VLAN4_anon: port 1(eth1.4) entered disabled state [21215.603598] device eth1.4 entered promiscuous mode [21215.605815] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [21215.607295] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [21215.614389] device wlan0-2 entered promiscuous mode [21215.630461] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [21215.630495] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [21215.640976] device wlan1-2 entered promiscuous mode [21215.643822] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [21215.646390] br-VLAN4_anon: port 3(wlan1-2) entered forwarding state [21215.652612] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [21215.658701] br-VLAN4_anon: port 2(wlan0-2) entered forwarding state [21215.664937] br-VLAN4_anon: port 1(eth1.4) entered blocking state [21215.670952] br-VLAN4_anon: port 1(eth1.4) entered forwarding state [21290.513729] br-VLAN3_guest: port 3(wlan1-1) entered disabled state [21290.513797] br-VLAN3_guest: port 2(wlan0-1) entered disabled state [21290.518876] br-VLAN3_guest: port 1(eth1.3) entered disabled state [21290.532875] device eth1.3 left promiscuous mode [21290.532993] br-VLAN3_guest: port 1(eth1.3) entered disabled state [21290.605554] device wlan0-1 left promiscuous mode [21290.605659] br-VLAN3_guest: port 2(wlan0-1) entered disabled state [21290.635795] device wlan1-1 left promiscuous mode [21290.635873] br-VLAN3_guest: port 3(wlan1-1) entered disabled state [21290.808752] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [21290.808813] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [21290.813860] br-VLAN4_anon: port 1(eth1.4) entered disabled state [21290.827134] device eth1.4 left promiscuous mode [21290.827225] br-VLAN4_anon: port 1(eth1.4) entered disabled state [21290.905457] device wlan0-2 left promiscuous mode [21290.905562] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [21290.945537] device wlan1-2 left promiscuous mode [21290.945610] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [21291.117679] br-VLAN3_guest: port 1(eth1.3) entered blocking state [21291.117711] br-VLAN3_guest: port 1(eth1.3) entered disabled state [21291.123030] device eth1.3 entered promiscuous mode [21291.134920] br-VLAN3_guest: port 2(wlan0-1) entered blocking state [21291.134944] br-VLAN3_guest: port 2(wlan0-1) entered disabled state [21291.140283] device wlan0-1 entered promiscuous mode [21291.150580] br-VLAN3_guest: port 3(wlan1-1) entered blocking state [21291.151037] br-VLAN3_guest: port 3(wlan1-1) entered disabled state [21291.158130] device wlan1-1 entered promiscuous mode [21291.166268] br-VLAN3_guest: port 3(wlan1-1) entered blocking state [21291.168118] br-VLAN3_guest: port 3(wlan1-1) entered forwarding state [21291.174496] br-VLAN3_guest: port 2(wlan0-1) entered blocking state [21291.180926] br-VLAN3_guest: port 2(wlan0-1) entered forwarding state [21291.186981] br-VLAN3_guest: port 1(eth1.3) entered blocking state [21291.193384] br-VLAN3_guest: port 1(eth1.3) entered forwarding state [21291.208175] br-VLAN4_anon: port 1(eth1.4) entered blocking state [21291.208200] br-VLAN4_anon: port 1(eth1.4) entered disabled state [21291.213941] device eth1.4 entered promiscuous mode [21291.221447] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [21291.223909] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [21291.231025] device wlan0-2 entered promiscuous mode [21291.238668] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [21291.240765] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [21291.247936] device wlan1-2 entered promiscuous mode [21291.255022] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [21291.257843] br-VLAN4_anon: port 3(wlan1-2) entered forwarding state [21291.264170] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [21291.270186] br-VLAN4_anon: port 2(wlan0-2) entered forwarding state [21291.276494] br-VLAN4_anon: port 1(eth1.4) entered blocking state [21291.282433] br-VLAN4_anon: port 1(eth1.4) entered forwarding state [22675.789035] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22675.789109] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22675.794225] br-VLAN4_anon: port 1(eth1.4) entered disabled state [22675.821781] device eth1.4 left promiscuous mode [22675.821902] br-VLAN4_anon: port 1(eth1.4) entered disabled state [22675.920423] device wlan0-2 left promiscuous mode [22675.920539] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22675.952228] device wlan1-2 left promiscuous mode [22675.952330] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22676.143255] br-VLAN4_anon: port 1(eth1.4) entered blocking state [22676.143280] br-VLAN4_anon: port 1(eth1.4) entered disabled state [22676.148518] device eth1.4 entered promiscuous mode [22676.180371] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [22676.180396] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22676.185664] device wlan0-2 entered promiscuous mode [22676.201928] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [22676.201952] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22676.207212] device wlan1-2 entered promiscuous mode [22676.242106] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [22676.242131] br-VLAN4_anon: port 3(wlan1-2) entered forwarding state [22676.247248] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [22676.253354] br-VLAN4_anon: port 2(wlan0-2) entered forwarding state [22676.259566] br-VLAN4_anon: port 1(eth1.4) entered blocking state [22676.265671] br-VLAN4_anon: port 1(eth1.4) entered forwarding state [22676.352379] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22676.352448] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22676.357490] br-VLAN4_anon: port 1(eth1.4) entered disabled state [22676.383513] device eth1.4 left promiscuous mode [22676.383644] br-VLAN4_anon: port 1(eth1.4) entered disabled state [22676.480300] device wlan0-2 left promiscuous mode [22676.480405] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22676.510513] device wlan1-2 left promiscuous mode [22676.510592] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22676.660953] br-VLAN4_anon: port 1(eth1.4) entered blocking state [22676.660977] br-VLAN4_anon: port 1(eth1.4) entered disabled state [22676.666286] device eth1.4 entered promiscuous mode [22676.674199] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [22676.676624] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22676.683085] device wlan0-2 entered promiscuous mode [22676.693190] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [22676.693537] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22676.699971] device wlan1-2 entered promiscuous mode [22676.711633] br-VLAN4_anon: port 3(wlan1-2) entered blocking state [22676.711658] br-VLAN4_anon: port 3(wlan1-2) entered forwarding state [22676.716842] br-VLAN4_anon: port 2(wlan0-2) entered blocking state [22676.722949] br-VLAN4_anon: port 2(wlan0-2) entered forwarding state [22676.729189] br-VLAN4_anon: port 1(eth1.4) entered blocking state [22676.735289] br-VLAN4_anon: port 1(eth1.4) entered forwarding state [22676.965784] ath10k_pci 0000:01:00.0: No VIF found for vdev 2 [22676.965808] ath10k_pci 0000:01:00.0: no vif for vdev_id 2 found [22677.003542] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 2 [22677.003917] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22677.015569] device wlan0-2 left promiscuous mode [22677.015600] br-VLAN4_anon: port 2(wlan0-2) entered disabled state [22677.211971] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22677.214640] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 2 [22677.219469] device wlan1-2 left promiscuous mode [22677.223935] br-VLAN4_anon: port 3(wlan1-2) entered disabled state [22677.431661] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 1 [22677.431721] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 1 [22677.437991] br-VLAN3_guest: port 3(wlan1-1) entered disabled state [22677.464034] device wlan1-1 left promiscuous mode [22677.464067] br-VLAN3_guest: port 3(wlan1-1) entered disabled state [22677.660715] device wlan1 left promiscuous mode [22677.660819] br-lan: port 2(wlan1) entered disabled state [22677.734807] ath10k_pci 0001:01:00.0: mac flush null vif, drop 0 queues 0xffff [22677.736670] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0 [22677.741015] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0 [22677.911804] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1 [22677.911829] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1 [22677.913494] br-VLAN3_guest: port 2(wlan0-1) entered disabled state [22677.951646] device wlan0-1 left promiscuous mode [22677.951679] br-VLAN3_guest: port 2(wlan0-1) entered disabled state [22678.220448] device wlan0 left promiscuous mode [22678.220559] br-lan: port 3(wlan0) entered disabled state [22678.272854] ath10k_pci 0000:01:00.0: mac flush null vif, drop 0 queues 0xffff [22678.273719] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0 [22678.278994] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0 [22684.954168] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [22684.954194] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [22685.036876] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [22685.037685] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [22685.463357] ath10k_pci 0001:01:00.0: rts threshold -1 [22685.463767] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [22685.478843] br-lan: port 2(wlan1) entered blocking state [22685.478878] br-lan: port 2(wlan1) entered disabled state [22685.484240] device wlan1 entered promiscuous mode [22685.860664] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [22685.860828] br-lan: port 2(wlan1) entered blocking state [22685.866090] br-lan: port 2(wlan1) entered forwarding state [22691.770176] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [22691.770204] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [22691.850759] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [22691.851505] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [22692.229096] ath10k_pci 0000:01:00.0: rts threshold -1 [22692.229472] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [22692.237629] br-lan: port 3(wlan0) entered blocking state [22692.244185] br-lan: port 3(wlan0) entered disabled state [22692.249927] device wlan0 entered promiscuous mode [22692.259987] br-VLAN3_guest: port 2(wlan1-1) entered blocking state [22692.260172] br-VLAN3_guest: port 2(wlan1-1) entered disabled state [22692.265676] device wlan1-1 entered promiscuous mode [22692.278118] ath10k_pci 0001:01:00.0: rts threshold -1 [22692.279878] br-VLAN3_guest: port 2(wlan1-1) entered blocking state [22692.282215] br-VLAN3_guest: port 2(wlan1-1) entered forwarding state [22692.342978] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready [22692.345632] br-VLAN4_anon: port 2(wlan1-2) entered blocking state [22692.348393] br-VLAN4_anon: port 2(wlan1-2) entered disabled state [22692.354875] device wlan1-2 entered promiscuous mode [22692.364380] ath10k_pci 0001:01:00.0: rts threshold -1 [22692.367039] br-VLAN4_anon: port 2(wlan1-2) entered blocking state [22692.370627] br-VLAN4_anon: port 2(wlan1-2) entered forwarding state [22692.386608] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-2: link becomes ready [22692.873327] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [22692.873608] br-lan: port 3(wlan0) entered blocking state [22692.878830] br-lan: port 3(wlan0) entered forwarding state [22692.894094] br-VLAN3_guest: port 3(wlan0-1) entered blocking state [22692.894119] br-VLAN3_guest: port 3(wlan0-1) entered disabled state [22692.899634] device wlan0-1 entered promiscuous mode [22692.915393] ath10k_pci 0000:01:00.0: rts threshold -1 [22692.922384] br-VLAN3_guest: port 3(wlan0-1) entered blocking state [22692.922416] br-VLAN3_guest: port 3(wlan0-1) entered forwarding state [22692.992802] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready [22692.995011] br-VLAN4_anon: port 3(wlan0-2) entered blocking state [22692.998218] br-VLAN4_anon: port 3(wlan0-2) entered disabled state [22693.004674] device wlan0-2 entered promiscuous mode [22693.017546] ath10k_pci 0000:01:00.0: rts threshold -1 [22693.024557] br-VLAN4_anon: port 3(wlan0-2) entered blocking state [22693.024584] br-VLAN4_anon: port 3(wlan0-2) entered forwarding state [22693.052953] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-2: link becomes ready [82924.705282] 8<--- cut here --- [82924.705303] Unable to handle kernel NULL pointer dereference at virtual address 00000030 [82924.707228] pgd = b3635b07 [82924.717072] [00000030] *pgd=00000000 [82924.717987] Internal error: Oops: 5 [#1] SMP ARM [82924.721716] Modules linked in: xt_connlimit pppoe ppp_async nf_conncount iptable_nat ath10k_pci ath10k_core ath xt_state xt_nat xt_helper xt_conntrack xt_connmark xt_connbytes xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table_hw nf_flow_table nf_conntrack_netlink nf_conntrack mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_recent xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_ecn xt_dscp xt_comment xt_TCPMSS xt_LOG xt_HL xt_DSCP xt_CLASSIFY slhc sch_cake nfnetlink nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables crc_ccitt compat sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_tcindex cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred ledtrig_usbport nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb tun uas usb_storage leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 [82924.721816] dwc3_qcom ohci_platform ohci_hcd phy_qcom_ipq806x_usb ahci fsl_mph_dr_of ehci_platform ehci_fsl sd_mod ahci_platform libahci_platform libahci libata scsi_mod ehci_hcd gpio_button_hotplug ext4 mbcache jbd2 crc32c_generic [82924.813582] CPU: 0 PID: 1690 Comm: kworker/0:0 Not tainted 5.4.119 #0 [82924.834131] Hardware name: Generic DT based system [82924.840472] Workqueue: events 0xc072e4bc [82924.845152] PC is at 0xc0616e78 [82924.849231] LR is at 0xc0616e74 [82924.852095] pc : [] lr : [] psr: a0000013 [82924.855224] sp : ce659db8 ip : c0c1c8e0 fp : 00000010 [82924.861473] r10: 00000003 r9 : 00000000 r8 : dd61cf00 [82924.866682] r7 : dd512300 r6 : ce659e14 r5 : ce659dcc r4 : dd51c8e0 [82924.871892] r3 : 00000000 r2 : dd51c6c0 r1 : ce659dcc r0 : dd51c8e0 [82924.878491] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [82924.885002] Control: 10c5787d Table: 58d3406a DAC: 00000051 [82924.892206] Process kworker/0:0 (pid: 1690, stack limit = 0xc5d4180d) [82924.897934] Stack: (0xce659db8 to 0xce65a000) [82924.904359] 9da0: 00000000 00000000 [82924.908712] 9dc0: ce659e14 c0619fb4 00000000 16e36000 00000000 ffffffff 00000000 dd51c6c0 [82924.916871] 9de0: 16e36000 dd61cf00 16e36000 16e36000 dd512300 00000002 c0c68e8c dce4f4c0 [82924.925031] 9e00: dce4f4d8 c0617568 dce4e434 00000000 ffffffff 16e36000 00000000 ffffffff [82924.933190] 9e20: 3b9aca00 c0c1c8e0 00000000 dd61cf00 16e36000 16e36000 00000000 00000002 [82924.941351] 9e40: c0c68e8c c0618d58 c0c28144 16e36000 00000000 ffffffff 16e36000 dd6e4d58 [82924.949509] 9e60: dcc55c00 dce4f500 16e36000 66d16940 47868c00 c0618f60 dcc55c00 66d16940 [82924.957670] 9e80: 66d16940 c072f470 00000000 001a5248 dce4f500 dce4e580 dcc55c00 dcc55c00 [82924.965830] 9ea0: 00000000 c0c68e70 00000000 00000005 001a5248 00000000 ffffe000 c072a0e0 [82924.973991] 9ec0: dcc55c00 000927c0 001a5248 000000a1 dcc55c00 dce4e600 dce4f680 dce4e680 [82924.982149] 9ee0: dce4e680 dce4f680 00000000 c072d928 dce4e638 00000000 dce4e604 dcc55c00 [82924.990309] 9f00: c0c28438 00000000 00000000 c072e4f4 dce4e638 d8585f00 ddb93680 ddb96800 [82924.998469] 9f20: 00000000 c03377c0 00000008 c0c03d00 d8585f00 d8585f14 ddb93680 00000008 [82925.006628] 9f40: c0c03d00 ddb93698 ddb93680 c0337a80 c0c0bdb8 c0922d4c ffffe000 c0337a2c [82925.014787] 9f60: d8585f00 dc1f6b40 dc1f6800 00000000 ce658000 c0337a2c d8585f00 d77c3eac [82925.022947] 9f80: dc1f6b5c c033da30 00000000 dc1f6800 c033d8d0 00000000 00000000 00000000 [82925.031110] 9fa0: 00000000 00000000 00000000 c03010e8 00000000 00000000 00000000 00000000 [82925.039266] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [82925.047427] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [82925.055579] Function entered at [] from [] [82925.063732] Function entered at [] from [] [82925.069460] Function entered at [] from [] [82925.075277] Function entered at [] from [] [82925.081093] Function entered at [] from [] [82925.086910] Function entered at [] from [] [82925.092723] Function entered at [] from [] [82925.098541] Function entered at [] from [] [82925.104356] Function entered at [] from [] [82925.110174] Function entered at [] from [] [82925.115988] Function entered at [] from [] [82925.121805] Function entered at [] from [] [82925.127620] Exception stack(0xce659fb0 to 0xce659ff8) [82925.133441] 9fa0: 00000000 00000000 00000000 00000000 [82925.138572] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [82925.146728] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [82925.154888] Code: e1a01005 e1a00004 ebfffcb2 e5943004 (e5932030) [82925.161404] ---[ end trace 7597597a4ac4197f ]--- [82925.167622] Kernel panic - not syncing: Fatal exception [82925.172249] CPU1: stopping [82925.177195] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 5.4.119 #0 [82925.179971] Hardware name: Generic DT based system [82925.187523] Function entered at [] from [] [82925.192123] Function entered at [] from [] [82925.197938] Function entered at [] from [] [82925.203753] Function entered at [] from [] [82925.209570] Function entered at [] from [] [82925.215385] Exception stack(0xdd46bf18 to 0xdd46bf60) [82925.221208] bf00: 00000000 00004b6b [82925.226348] bf20: 1d061000 ddba2a80 dcc6a400 00000000 ddba1e30 00004b6b 00004b6b 00000000 [82925.234507] bf40: 856f2f20 852d3b60 00000015 dd46bf68 c0730ab8 c0730abc 90000013 ffffffff [82925.242649] Function entered at [] from [] [82925.250803] Function entered at [] from [] [82925.256531] Function entered at [] from [] [82925.262347] Function entered at [] from [] [82925.268163] Function entered at [] from [<423024cc>] [82925.273983] Rebooting in 3 seconds.. U-Boot 2012.07 [Standard IPQ806X.LN,unknown] (Oct 03 2018 - 18:59:17) smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000 4 MiB MMC: ipq_mmc: 0 In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS cdp: get part failed for rootfs Net: MAC1 addr:a:b:XX:dd:ff:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:a:b:XX:dd:ff:2 Disable WAN port eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 0a:0b:XX:dd:ff:01 Address in environment is cc:dd:XX:aa:ff:04 , eth1 ZyXEL zloader v2.07 (Oct 03 2018 - 19:00:54) MMC read: dev # 0, block # 16418, count 4 ... MMC read: dev # 0, block # 16418, count 4 ... Multiboot clinent version: 2.0 Mac1 unit failed Hit any key to stop autoboot: 3 [trimmed] MMC read: dev # 0, block # 18466, count 8192 ... 8192 blocks read: OK Image Name: ARM OpenWrt Linux-5.4.119 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2746210 Bytes = 2.6 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK device nand1 , # parts = 8 #: name size offset mask_flags 0: SBL 0x000c0000 0x00000000 1 1: TZ 0x00040000 0x000c0000 1 2: RPM 0x00040000 0x00100000 1 3: u-boot 0x00080000 0x00140000 1 4: env 0x00010000 0x001c0000 1 5: ART 0x00010000 0x001d0000 1 6: dualflag 0x00010000 0x001e0000 0 7: reserved 0x00210000 0x001f0000 0 active partition: nand1,0 - (SBL) 0x000c0000 @ 0x00000000 defaults: mtdids : none mtdparts: mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,${ldr_psize}(u-boot)${readonly},${env_psize}(env)${readonly},${rfdat_psize}(ART)${readonly},${dualflag_psize}(dualflag),${reserved_psize}(reserved) Setting up atags for msm partition: SBL Setting up atags for msm partition: TZ Setting up atags for msm partition: RPM Setting up atags for msm partition: u-boot Setting up atags for msm partition: env Setting up atags for msm partition: ART Setting up atags for msm partition: dualflag Setting up atags for msm partition: reserved Using machid 0x136d from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.119 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16122-c2139eef27)) #0 SMP Fri May 28 14:04:04 2021 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NBG6817 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu s30220 r8192 d23028 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800 [ 0.000000] Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5 [ 0.000000] Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.07 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 476880K/491520K available (6259K kernel code, 196K rwdata, 916K rodata, 1024K init, 240K bss, 14640K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from 0xc0b00c18 with crng_init=0 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000019] Switching to timer-based delay loop, resolution 160ns [ 0.000221] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000240] pid_max: default: 32768 minimum: 301 [ 0.000412] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000430] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001371] CPU: Testing write buffer coherency: ok [ 0.002456] Setting up static identity map for 0x42300000 - 0x42300060 [ 0.002622] rcu: Hierarchical SRCU implementation. [ 0.003079] smp: Bringing up secondary CPUs ... [ 0.004931] smp: Brought up 1 node, 2 CPUs [ 0.004945] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.004954] CPU: All CPU(s) started in SVC mode. [ 0.014188] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.014331] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.014357] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.014489] pinctrl core: initialized pinctrl subsystem [ 0.015543] NET: Registered protocol family 16 [ 0.015854] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017134] cpuidle: using governor ladder [ 0.017196] cpuidle: using governor menu [ 0.047363] usbcore: registered new interface driver usbfs [ 0.047440] usbcore: registered new interface driver hub [ 0.047503] usbcore: registered new device driver usb [ 0.047559] pps_core: LinuxPPS API ver. 1 registered [ 0.047571] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.047609] PTP clock support registered [ 0.048322] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.049387] clocksource: Switched to clocksource dg_timer [ 0.050198] thermal_sys: Registered thermal governor 'step_wise' [ 0.052643] NET: Registered protocol family 2 [ 0.052800] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.053601] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.053638] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.053687] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.053740] TCP: Hash tables configured (established 4096 bind 4096) [ 0.053834] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.053861] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.054087] NET: Registered protocol family 1 [ 0.054139] PCI: CLS 0 bytes, default 64 [ 0.055369] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.062116] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.062130] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.100385] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.102039] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator [ 0.102167] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.102267] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.102517] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: [ 0.102580] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.102616] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.325097] qcom-pcie 1b500000.pci: Link up [ 0.325247] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.325268] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.325285] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.325301] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.325357] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.325509] pci 0000:00:00.0: supports D1 [ 0.325524] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.329384] PCI: bus0: Fast back to back transfers disabled [ 0.329816] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.330169] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.331319] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.335380] PCI: bus1: Fast back to back transfers disabled [ 0.335460] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.335484] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.335608] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.335628] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.336320] pcieport 0000:00:00.0: AER: enabled with IRQ 36 [ 0.336824] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator [ 0.336940] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.337056] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.337293] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: [ 0.337352] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.337386] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.566800] qcom-pcie 1b700000.pci: Link up [ 0.566953] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.566972] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.566988] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.567041] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.567184] pci 0001:00:00.0: supports D1 [ 0.567198] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.571075] PCI: bus0: Fast back to back transfers disabled [ 0.571403] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.571779] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.573013] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.573311] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 0.577122] PCI: bus1: Fast back to back transfers disabled [ 0.577193] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.577216] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.577348] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.577368] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.578131] pcieport 0001:00:00.0: AER: enabled with IRQ 38 [ 0.580577] L2 @ QSB rate. Forcing new rate. [ 0.580788] L2 @ 384000 KHz [ 0.580966] CPU0 @ 800000 KHz [ 0.580978] CPU1 @ QSB rate. Forcing new rate. [ 0.581107] CPU1 @ 384000 KHz [ 0.584623] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.585991] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0 [ 0.587621] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.590079] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.590127] msm_serial 16340000.serial: uartclk = 7372800 [ 0.590192] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM [ 0.590227] msm_serial: console setup on port #0 [ 1.406985] printk: console [ttyMSM0] enabled [ 1.412042] msm_serial: driver initialized [ 1.421044] loop: module loaded [ 1.422080] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 1.425064] spi-nor spi0.0: mx25u3235f (4096 Kbytes) [ 1.430497] 13 qcom-smem partitions found on MTD device spi0.0 [ 1.435373] Creating 13 MTD partitions on "spi0.0": [ 1.441098] 0x000000000000-0x000000020000 : "0:SBL1" [ 1.446717] 0x000000020000-0x000000040000 : "0:MIBIB" [ 1.451969] 0x000000040000-0x000000060000 : "0:SBL2" [ 1.456850] 0x000000060000-0x0000000a0000 : "0:SBL3" [ 1.461957] 0x0000000a0000-0x0000000b0000 : "0:DDRCONFIG" [ 1.466799] 0x0000000b0000-0x0000000c0000 : "0:SSD" [ 1.472201] 0x0000000c0000-0x000000100000 : "0:TZ" [ 1.476790] 0x000000100000-0x000000140000 : "0:RPM" [ 1.481727] 0x000000140000-0x0000001c0000 : "0:APPSBL" [ 1.486422] 0x0000001c0000-0x0000001d0000 : "0:APPSBLENV" [ 1.491747] 0x0000001d0000-0x0000001e0000 : "0:ART" [ 1.497104] 0x0000001e0000-0x0000001f0000 : "0:DUAL_FLAG" [ 1.501883] 0x0000001f0000-0x000000400000 : "0:RESERVED" [ 1.508526] libphy: ipq8064_mdio_bus: probed [ 1.527167] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii [ 2.376069] ar8327: qca,phy-rgmii-en is not specified [ 2.376599] libphy: Fixed MDIO Bus: probed [ 2.380822] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found [ 2.384101] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found [ 2.391582] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock [ 2.398200] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.404324] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000 [ 2.411776] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported [ 2.417518] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported [ 2.425331] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2 [ 2.433203] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported [ 2.438959] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported [ 2.446417] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors [ 2.453195] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors [ 2.460724] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled [ 2.467690] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.473948] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 8a:b3:75:cf:80:89 [ 2.483439] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found [ 2.490343] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found [ 2.497658] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock [ 2.504205] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.510526] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000 [ 2.517874] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported [ 2.523777] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported [ 2.531494] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2 [ 2.539312] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported [ 2.545207] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported [ 2.552611] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors [ 2.559278] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors [ 2.566918] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled [ 2.573962] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.580143] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 02:04:ec:7e:31:d5 [ 2.590355] i2c /dev entries driver [ 2.599704] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.599986] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.608514] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 34,0 (pio) [ 2.614640] mmci-pl18x 12400000.sdcc: DMA channels RX dma0chan1, TX dma0chan2 [ 2.649023] sdhci: Secure Digital Host Controller Interface driver [ 2.649058] sdhci: Copyright(c) Pierre Ossman [ 2.654216] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.662106] NET: Registered protocol family 10 [ 2.666282] Segment Routing with IPv6 [ 2.668654] NET: Registered protocol family 17 [ 2.672449] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.677037] 8021q: 802.1Q VLAN Support v1.8 [ 2.689952] Registering SWP/SWPB emulation handler [ 2.727775] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364 [ 2.744387] s1a: Bringing 0uV into 1050000-1050000uV [ 2.744798] s1a: supplied by regulator-dummy [ 2.748706] s1b: Bringing 0uV into 1050000-1050000uV [ 2.753107] s1b: supplied by regulator-dummy [ 2.757827] s2a: Bringing 0uV into 775000-775000uV [ 2.762320] s2a: supplied by regulator-dummy [ 2.766689] s2b: Bringing 0uV into 775000-775000uV [ 2.771339] s2b: supplied by regulator-dummy [ ÿ[ 2.788314] Waiting for root device /dev/mmcblk0p5... [ 2.821271] mmc0: new high speed MMC card at address 0001 [ 2.822327] mmcblk0: mmc0:0001 M62704 3.53 GiB [ 2.826038] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB [ 2.830552] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB [ 2.836041] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB, chardev (247:0) [ 2.844332] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 [ 2.873880] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 2.876153] Freeing unused kernel memory: 1024K [ 2.920011] Run /sbin/init as init process [ 3.134428] random: fast init done [ 3.335016] init: Console is alive [ 3.335140] init: - watchdog - [ 3.695073] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.736689] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.739077] SCSI subsystem initialized [ 3.748193] ehci-fsl: Freescale EHCI Host controller driver [ 3.748564] ehci-platform: EHCI generic platform driver [ 3.755170] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.758067] ohci-platform: OHCI generic platform driver [ 3.766768] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found [ 3.769140] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found [ 3.775123] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found [ 3.781169] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found [ 3.788754] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found [ 3.792828] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found [ 3.798482] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found [ 3.804641] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found [ 3.822019] dwc3 11000000.dwc3: Failed to get clk 'ref': -2 [ 3.884718] dwc3 10000000.dwc3: Failed to get clk 'ref': -2 [ 3.961061] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.961100] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.965575] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 3.973084] xhci-hcd xhci-hcd.0.auto: irq 44, io mem 0x11000000 [ 3.983088] hub 1-0:1.0: USB hub found [ 3.988286] hub 1-0:1.0: 1 port detected [ 3.992317] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.996166] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 4.001516] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 4.009841] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.015934] hub 2-0:1.0: USB hub found [ 4.023930] hub 2-0:1.0: 1 port detected [ 4.027673] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.031573] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 4.036915] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 4.044426] xhci-hcd xhci-hcd.1.auto: irq 45, io mem 0x10000000 [ 4.054292] hub 3-0:1.0: USB hub found [ 4.059728] hub 3-0:1.0: 1 port detected [ 4.063609] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.067519] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 4.072897] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 4.081804] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.087287] hub 4-0:1.0: USB hub found [ 4.095300] hub 4-0:1.0: 1 port detected [ 4.100069] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.106281] init: - preinit - [ 4.362663] random: jshn: uninitialized urandom read (4 bytes read) [ 4.380873] random: jshn: uninitialized urandom read (4 bytes read) [ 4.389891] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 4.423975] random: procd: uninitialized urandom read (4 bytes read) [ 4.430127] usb 3-1: new high-speed USB device number 2 using xhci-hcd Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.846304] EXT4-fs (loop0): recovery complete [ 7.847142] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 7.852930] mount_root: loading kmods from internal overlay [ 7.914023] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 7.917940] usb-storage 3-1:1.0: USB Mass Storage device detected [ 7.921676] scsi host0: usb-storage 3-1:1.0 [ 7.927713] usbcore: registered new interface driver usb-storage [ 7.935726] scsi host1: uas [ 7.937886] usbcore: registered new interface driver uas [ 7.940751] scsi 1:0:0:0: Direct-Access Seagate Expansion 060E PQ: 0 ANSI: 6 [ 7.945838] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 7.954792] sd 1:0:0:0: [sda] Spinning up disk... [ 8.128713] random: crng init done [ 8.128732] random: 3 urandom warning(s) missed due to ratelimiting [ 8.971936] scsi 0:0:0:0: Direct-Access Sony Storage Media 0100 PQ: 0 ANSI: 0 CCS [ 8.974175] sd 0:0:0:0: [sdb] 1966080 512-byte logical blocks: (1.01 GB/960 MiB) [ 8.980679] sd 0:0:0:0: [sdb] Write Protect is off [ 8.988084] sd 0:0:0:0: [sdb] No Caching mode page found [ 8.991480] sd 0:0:0:0: [sdb] Assuming drive cache: write through [ 9.005106] sdb: sdb1 sdb2 [ 9.009018] sd 0:0:0:0: [sdb] Attached SCSI removable disk [ 9.049786] .ready [ 9.051207] sd 1:0:0:0: [sda] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB) [ 9.223409] sd 1:0:0:0: [sda] Write Protect is off [ 9.224069] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.227736] sd 1:0:0:0: [sda] Optimal transfer size 33553920 bytes [ 9.245356] sda: sda1 [ 9.248513] sd 1:0:0:0: [sda] Attached SCSI disk [ 9.431227] block: attempting to load /etc/config/fstab [ 9.431396] block: unable to load configuration (fstab: Entry not found) [ 9.435304] block: no usable configuration [ 9.443035] mount_root: switching to ext4 overlay [ 9.449530] urandom-seed: Seeding with /etc/urandom.seed [ 9.488542] procd: - early - [ 9.488647] procd: - watchdog - [ 10.085559] procd: - watchdog - [ 10.089835] procd: - ubus - [ 10.145136] procd: - init - Please press Enter to activate this console. [ 10.463616] urngd: v1.0.2 started. [ 10.523670] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.525569] tun: Universal TUN/TAP device driver, 1.6 [ 10.560751] Mirror/redirect action on [ 10.563350] u32 classifier [ 10.563378] input device check on [ 10.565988] Actions configured [ 10.573304] Loading modules backported from Linux version v5.10.34-0-g0aa66717f684 [ 10.573328] Backport generated by backports.git v5.10.34-1-0-g7b5533e1 [ 10.590798] xt_time: kernel timezone is -0000 [ 10.624472] PPP generic driver version 2.4.2 [ 10.624914] NET: Registered protocol family 24 [ 10.642376] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 10.642833] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 10.649831] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 17.195892] EXT4-fs (sdb1): mounting ext2 file system using the ext4 subsystem [ 17.207633] EXT4-fs (sdb1): warning: mounting unchecked fs, running e2fsck is recommended [ 17.209577] EXT4-fs (sdb1): mounted filesystem without journal. Opts: [ 19.485585] EXT4-fs (sda1): recovery complete [ 19.520484] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: [ 22.166732] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 22.166787] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 22.180651] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 [ 24.507213] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734 [ 28.030590] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 28.030620] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 28.111153] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 28.111980] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 28.396357] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 28.494761] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 28.496125] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 28.502607] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 28.988712] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 28.988747] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 29.000245] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 [ 31.319940] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734 [ 34.853610] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 34.853637] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 34.936171] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 34.937018] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 35.272125] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 35.373157] kmodloader: done loading kernel modules from /etc/modules.d/* [ 39.442941] dwmac1000: Master AXI performs any burst length [ 39.443392] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found [ 39.447327] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 39.455489] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 39.464844] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode [ 39.472554] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 39.475949] br-VLAN3_guest: port 1(eth1.3) entered blocking state [ 39.488643] br-VLAN3_guest: port 1(eth1.3) entered disabled state [ 39.494927] device eth1.3 entered promiscuous mode [ 39.500861] device eth1 entered promiscuous mode [ 39.507180] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 39.510782] br-VLAN3_guest: port 1(eth1.3) entered blocking state [ 39.516249] br-VLAN3_guest: port 1(eth1.3) entered forwarding state [ 39.567221] br-VLAN4_anon: port 1(eth1.4) entered blocking state [ 39.567249] br-VLAN4_anon: port 1(eth1.4) entered disabled state [ 39.572513] device eth1.4 entered promiscuous mode [ 39.583150] br-VLAN4_anon: port 1(eth1.4) entered blocking state [ 39.583177] br-VLAN4_anon: port 1(eth1.4) entered forwarding state [ 39.608495] br-lan: port 1(eth1.1) entered blocking state [ 39.608525] br-lan: port 1(eth1.1) entered disabled state [ 39.616444] device eth1.1 entered promiscuous mode [ 39.624404] br-lan: port 1(eth1.1) entered blocking state [ 39.624429] br-lan: port 1(eth1.1) entered forwarding state [ 39.639848] dwmac1000: Master AXI performs any burst length [ 39.639881] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found [ 39.644235] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 39.652397] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 39.661311] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode [ 39.668617] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 39.683826] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 40.569825] IPv6: ADDRCONF(NETDEV_CHANGE): br-VLAN3_guest: link becomes ready [ 46.584295] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 46.584321] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 46.666936] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 46.667758] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 47.108002] ath10k_pci 0001:01:00.0: rts threshold -1 [ 47.108861] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 47.123385] br-lan: port 2(wlan1) entered blocking state [ 47.123422] br-lan: port 2(wlan1) entered disabled state [ 47.128818] device wlan1 entered promiscuous mode [ 47.220305] ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 47.549493] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 47.549645] br-lan: port 2(wlan1) entered blocking state [ 47.554970] br-lan: port 2(wlan1) entered forwarding state [ 53.462317] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 53.462343] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 53.542760] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 53.543587] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 53.920701] ath10k_pci 0000:01:00.0: rts threshold -1 [ 53.920983] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 53.929328] br-lan: port 3(wlan0) entered blocking state [ 53.935768] br-lan: port 3(wlan0) entered disabled state [ 53.941579] device wlan0 entered promiscuous mode [ 53.946583] br-lan: port 3(wlan0) entered blocking state [ 53.951121] br-lan: port 3(wlan0) entered forwarding state [ 53.958011] br-lan: port 3(wlan0) entered disabled state [ 53.980621] br-VLAN3_guest: port 2(wlan1-1) entered blocking state [ 53.980650] br-VLAN3_guest: port 2(wlan1-1) entered disabled state [ 53.985894] device wlan1-1 entered promiscuous mode [ 54.003774] ath10k_pci 0001:01:00.0: rts threshold -1 [ 54.005531] br-VLAN3_guest: port 2(wlan1-1) entered blocking state [ 54.007800] br-VLAN3_guest: port 2(wlan1-1) entered forwarding state [ 54.082886] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready [ 54.086922] br-VLAN4_anon: port 2(wlan1-2) entered blocking state [ 54.088302] br-VLAN4_anon: port 2(wlan1-2) entered disabled state [ 54.094730] device wlan1-2 entered promiscuous mode [ 54.103650] ath10k_pci 0001:01:00.0: rts threshold -1 [ 54.107059] br-VLAN4_anon: port 2(wlan1-2) entered blocking state [ 54.110538] br-VLAN4_anon: port 2(wlan1-2) entered forwarding state [ 54.123562] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-2: link becomes ready [ 54.624123] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 54.624279] br-lan: port 3(wlan0) entered blocking state [ 54.629544] br-lan: port 3(wlan0) entered forwarding state [ 54.637537] br-VLAN3_guest: port 3(wlan0-1) entered blocking state [ 54.640222] br-VLAN3_guest: port 3(wlan0-1) entered disabled state [ 54.646488] device wlan0-1 entered promiscuous mode [ 54.658340] ath10k_pci 0000:01:00.0: rts threshold -1 [ 54.665594] br-VLAN3_guest: port 3(wlan0-1) entered blocking state [ 54.665620] br-VLAN3_guest: port 3(wlan0-1) entered forwarding state [ 54.719641] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready [ 54.721848] br-VLAN4_anon: port 3(wlan0-2) entered blocking state [ 54.725057] br-VLAN4_anon: port 3(wlan0-2) entered disabled state [ 54.731502] device wlan0-2 entered promiscuous mode [ 54.740827] ath10k_pci 0000:01:00.0: rts threshold -1 [ 54.744230] br-VLAN4_anon: port 3(wlan0-2) entered blocking state [ 54.747198] br-VLAN4_anon: port 3(wlan0-2) entered forwarding state [ 54.776240] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-2: link becomes ready [ 64.989491] ath10k_pci 0001:01:00.0: Invalid peer id 1 or peer stats buffer, peer: 5ac33392 sta: 00000000